Setting up A Bathtub
Setting up A Bathtub
Blog Article
How do you really feel about Installing A Bathtub?
Setting up a bathtub isn't exactly brain surgery, however it does need solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately hard job. If the old tub is conveniently obtainable, the job can move speedily; if you need to open a wall surface to eliminate the old tub and place the new bathtub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as set in the brand-new one. Ensure you have actually certified yourself for the work as well as are comfortable trying it. Rather than working with a specialist to take control of a halfway-completed project, it is far better to think about using one before you begin. Possibilities are you may require a professional plumber to make tube links.
This short article will certainly help you mount a new tub in your bathroom if you have currently purchased a brand-new tub and also don't require to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist must consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will come from the pipelines. As soon as the supply pipes have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in place between the tap and also the sink. Safeguard the faucet in position with the maker supplied backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type needs to be attached to the faucet ends first, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the level checks out level.
To mount faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water system and examine all joints as well as new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as likewise examine the overflow electrical outlet and the regular outlet for leakages.
Lastly, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait till the tub has actually been utilized at the very least once as this will certainly settle it right into its final placement.
Getting ready for the Installment
First of all, the sustaining frame supplied with the bathroom should be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bathroom and the tiling, leading to problems with moisture as well as possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components as well as installations. They are offered in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split relatively early if you do not take into consideration this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is a good idea to fit the tiles using waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that write up on How to Install a Bathtub when browsing the internet. Are you aware of another person who is sincerely interested in Tools You Need to Install a New Bathtub ? Do not hesitate to share it. We truly appreciate reading our article about Tools You Need to Install a New Bathtub .
About
Report this page